宏指令1

macro_command main()
short count,Realcount,i,baseaddress,getaddress,baseadd2,getadd2,on,baseadd3,getadd3,view,PLCAddr
int tempdata,realdata
unsigned char RealName[8]

//view=34
i=0
count=0
//temp baseaddr
baseaddress=910
// realdata baseaddr
Realcount=0
//PLC Addr
PLCAddr=2000
//SetData(view, "Local HMI", LW, 0, 1)
for i=0 to 7 step 1
RealName=''
next i
//獲取當前配方序號
GetData(count, "Local HMI", RW, 900, 1)
//設置載入當前配方序號
SetData(count, "Local HMI", RW, 900, 1)
//獲取實際數據基地址
getaddress= baseaddress+100*count
//獲取實際數據點數及配方名稱
GetData(Realcount, "Local HMI", RW, getaddress-9, 1)
GetData(RealName[0], "Local HMI", RW,getaddress-8, 8)
//設置實際數據點數及配方名稱
SetData(Realcount, "Local HMI", RW, 901, 1)
SetData(RealName[0], "Local HMI", RW, 902, 8)
DELAY(5)
//load other configure data for  XYZW
for i=0 to 60 step 2
     GetData(realdata, "Local HMI", RW,getaddress+i, 1)
     SetData(realdata, "Local HMI", RW,baseaddress+i, 1)  
next i
DELAY(1000)
//send data to PLC
SetData(Realcount, "DELTA DVP", D, 200, 1)
SetData(count, "DELTA DVP", D, 214, 1)
SetData(RealName[0], "DELTA DVP", D, 216, 8)
for i=0 to 60 step 2
     GetData(realdata, "Local HMI", RW,baseaddress+i, 1)
     SetData(realdata, "DELTA DVP", D, PLCAddr+i, 1)  
next i
DELAY(500)
//send exit cmd
on=1
SetData(on, "DELTA DVP", M, 1001, 1)


//view=0
//SetData(view, "Local HMI", LW, 0, 1)
//on=1
//SetData(on, "Local HMI", RW_Bit, 0, 1)
//SetData(on, "Local HMI", LB, 2, 1)

end macro_command




第二個宏指令
macro_command main()
short count,Realcount,i,number
short baseaddress,getaddress,view
int realdata,PLCAddr
unsigned char RealName[8]
i=0
count=0
baseaddress=910
Realcount=0
PLCAddr=2000
view=20
SetData(view, "Local HMI", LW, 10000, 1)
for i=0 to 7 step 1
RealName=''
next i
//view=35
//SetData(view, "Local HMI", LW, 0, 1)
//獲取PLC中實際配方數據,配方號，配方點數，配方名稱
//GetData(number, "DELTA DVP", D, 200, 1)
//GetData(Realcount, "DELTA DVP", D, 214, 1)
//GetData(RealName[0], "DELTA DVP", D, 216, 8)
//保存至HMI中臨時配方號，配方點數，配方名稱
//SetData(number, "Local HMI", RW, 900, 1)
//SetData(Realcount, "Local HMI", RW, 901, 1)
//SetData(RealName[0], "Local HMI", RW, 902, 8)
//保存至XYZ數據至臨時區域中
for i=0 to 60 step 2
     GetData(realdata, "DELTA DVP", D, PLCAddr+i, 1)
     SetData(realdata, "Local HMI", RW,baseaddress+i, 1)  
next i
DELAY(500)

//保存臨時數據至配方區域中
//***
GetData(number, "Local HMI", RW, 900, 1)
GetData(Realcount, "Local HMI", RW, 901, 1)
GetData(RealName[0], "Local HMI", RW, 902, 8)
SetData(number, "Local HMI", RW, baseaddress-10+100*number, 1)
SetData(Realcount, "Local HMI", RW, baseaddress-10+100*number+1, 1)
SetData(RealName[0], "Local HMI", RW, baseaddress-10+100*number+2, 8)
for i=0 to 60 step 2
     GetData(realdata, "Local HMI", RW, baseaddress+i, 1)
     SetData(realdata, "Local HMI", RW, baseaddress+100*number+i, 1)  
next i
DELAY(500)
view=0
SetData(view, "Local HMI", LW, 10000, 1)

end macro_command
看看這兩個宏指令，大家給點意見

學習啦。謝謝！

表示一點也看不懂,還是感謝分享!!!!!!!!!!

基本也看不懂